View AP9101C_8326976.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

AP9101C document numb er: ds37771 rev. 3 - 2 1 of 18 www.diodes.com december 2015 ? diodes incorporated AP9101C single chip solution for 1 - cell li+ battery pack description the ap9101 c is a protection ic developed for lithium - ion/lithium polymer rechargeable battery with a high - precision voltage , detection circuit. the ap9101 c provides a function to p rotect batteries by detecting overcharge voltage, overdischarge voltage, overcharge current, overdischarge current and other abnormalities and turning off the external mosfet switch. the ap9101 c also has a built - in fixed time circuit (external capacitors a re unnecessary) ; the protection circuitry can be comprised with fewer external components. the ap9101 c is available in standard packages of sot25 and sot26 . applications ? lithium - ion battery packs ? lithium polymer battery packs features ? low current consumption ( + 25c) ? operation mode: 3.0a ( typ ) v dd = 3.5v ? power - down mode: 0.01 a ( typ ) ? high - accuracy voltage detection circuit ( + 25c) ? overcharge detection voltage: 3.5v to 4.5v (5mv steps) accuracy 25mv ? overcharge hysteresis voltage range: 0.1v to 0 .4v (50mv steps) accuracy 50mv ? overdischarge detection voltage: 2.0v to 3.4v (10mv steps) accuracy 35mv ? overdischarge hysteresis voltage range: 0v to 0.7v (40mv steps) accuracy 65mv ? discharge overcurrent detection voltage: 0.05v to 0.32v (10mv steps) ac curacy 15mv ? short current detection voltage: 0.45v to 0.7v (50mv steps) accuracy 100mv ? charge overcurrent detection voltage: - 0.2v to - 0.05v (10mv steps) accuracy 15mv ? overcharger detection voltage: 8.0v (fixed) accuracy 2v ? overcharger release voltage: 7.3v (fixed) accuracy 2v ? built - i n fixed detection delay time ( + 25c): accuracy 20% ? power - down mode can be selectable: available/unavailable ? 0v battery charge function can be selectable : available/unavailable ? overcharge protection mode can be sel ectable : release/latch ? high - voltage cmos process : up to 30v between v dd and v m pins ? totally lead - free & fully rohs compliant (note 1 & 2) ? halogen and antimony free. green device (note 3) pin assignments notes: 1. no purposely added lead. fully eu directive 2002/95/ec (rohs) & 2011/65/eu (rohs 2) compliant. 2. see http://www.diodes.com/quality/lead_free.html for more information about diodes incorporate ds definitions of halogen - and antimony - free, "green" and lead - free. 3. halogen - and antimony - free "green products are defined as those which contain <9 00ppm bromine, <900ppm chlorine (<1500ppm total br + cl) and <1000ppm antimony compounds. sot25 sot26 ( top view ) (top view) v m v d d v s s d o c o 1 2 3 4 5 p i n 1 m a r k 6 n c v m v d d v s s d o c o p i n 1 m a r k 1 2 3 4 5
AP9101C document numb er: ds37771 rev. 3 - 2 2 of 18 www.diodes.com december 2015 ? diodes incorporated AP9101C typical applications circuit (note 4 ) note: 4. r1 and c1 are used to stabilize the supply voltage of the ap9101 c . the recommended range of r1 value is 330 to 470 and c1 value is 10nf to 1000nf, typical value is 100nf. r2 should be connected between p - to vm sense t erminal to monitor the status of charger and the charge / discharge current. the r2 should be between 300 and 4k , typical value is 2.7 k . r1 and r2 are also used as current limit resistor s if the battery or charger is connected reversely. polarity reversin g may cause the power consumption of r1 and r2 to go over the ir power dissipation rating, therefore r1 and r2 values should be selected appropriately for the actual application. if r2 is more than 4k resistor, co may not cut of f q2 due to the voltage dro p on r2. for power down mode, w hen first connecting ap9101 c system board to the battery, i t is necessary to use charger or to short p - to the battery negative polarity. once the AP9101C is activated, the charger or connection can be removed , otherwise the battery can not discharge current through system board. the values selected should follow the recommended typical range mentioned above. pin description s pin number pin name function sot25 sot26 1 2 v m charger negative input pin 2 5 v dd positive power input pin 3 6 v ss negative power input pin 4 1 do fet gate control pin for discharge 5 3 co fet gate control pin for c harge 4 nc no connected a p 9 1 0 1 c v d d v s s d o c o v m b a t t e r y r 1 3 3 0 t o 4 7 0 c 1 1 0 0 n f q 1 q 2 r 2 2 . 7 k p + p - 2 ( 5 ) 3 ( 6 ) 1 ( 2 ) 4 ( 1 ) 5 ( 3 ) a ( b ) a f o r s o t 2 5 b f o r s o t 2 6
AP9101C document numb er: ds37771 rev. 3 - 2 3 of 18 www.diodes.com december 2015 ? diodes incorporated AP9101C functional block diagram l o g i c c i r c u i t l o g i c c i r c u i t d e l a y t i m e c i r c u i t o v c h a r g e o p t i o n l e v e l s h i f t r v m d r v m s d o c o v m v s s v d d 1 ( 2 ) 5 ( 3 ) 4 ( 1 ) 2 ( 5 ) 3 ( 6 ) a ( b ) b f o r s o t 2 6 a f o r s o t 2 5
AP9101C document numb er: ds37771 rev. 3 - 2 4 of 18 www.diodes.com december 2015 ? diodes incorporated AP9101C absolut e maximum ratings ( note 5 ) symbol parameter rating unit v ds supply voltage (between v dd and v ss ) - 0.3 to 12 v v dm charger input voltage (between v dd and v m ) - 0.3 to 30 v v co co pin output voltage v m - 0.3 to v dd +0.3 v v do do pin output voltage v ss - 0.3 to v dd +0.3 v t opr operating t emperature range - 40 to + 85 c t j junction t emperature + 150 c t stg storage t emperature range - 65 to + 150 c t lead lead temperature (soldering, 10sec) + 300 c p d power dissipation ( + 25 c ) 250 mw esd ( machine model ) 200 v esd ( human body model) 2,000 v note: 5. stresses greater than those listed under absolute maximum ratings may cause permanent damage to the device. these are stres s ratings only, and functional operation of the device at these or any other condit ions beyond those indicated under recommended operating conditions is not implied. exposure to absolute maximum ratings for extended periods may affect device reliability. recommended operating conditions symbol parameter min max unit v ds supply vo ltage ( between v dd and v ss ) 1.5 5.5 v v dm charger input voltage (between v dd and v m ) - 0.3 5.5 v t a operating ambient temperature - 40 +85 c
AP9101C document numb er: ds37771 rev. 3 - 2 5 of 18 www.diodes.com december 2015 ? diodes incorporated AP9101C electrical characteristics ( t a = +25 c, v dd = 3.5v, v ss = 0v, r1 = 33 0? , r2 = 2.7 k?, c1 = 100nf, unless otherwise specified . ) symbol parameter test conditions min typ max unit v cu overcharge detection voltage v cu - 0.025 v cu v cu +0.025 v v cl overcharge release voltage v cl v cu v cl - 0.050 v cl v cl +0.050 v v cl = v cu v cl - 0. 025 v cl v cl +0.025 v v dl overdischarge detection voltage v dl - 0.035 v dl v dl +0.035 v v du overdischarge release voltage v du v dl v du - 0.10 0 v du v du +0.10 0 v v du = v dl v du - 0.035 v du v du +0.035 v v doc discharge overcurrent detection voltage v doc - 0.015 v d oc v doc +0.015 v v short load short - circuiting detection voltage v short - 0.10 v short v short +0.10 v v coc charge overcurrent detection voltage v coc - 0.015 v coc v coc +0.015 v i cc current consumption during operation v dd = 3.5v , v m = 0v 1.5 3 4.5 a i stb cu rrent consumption at power - down v dd = 1 .8v , v m pin floating power - down mode 0.1 a without power - down mode (auto - wake - up) 5.5 r coh co pin resistance h v dd = 3.5v, v co = 3.0v, v m = 0v 2 6 10 k ? r col co pin resistance l v dd = 4.5v, v co = 0.5v, v m = 0v 2 4 10 k? r doh do pin resistance h v dd = 3.5v, v do = 3.0v, v m = 0v 2 5 10 k? r dol do pin resistance l v dd = 1.8v, v do = 0.5v, v m = 0v 2 5 10 k? r vmd resistance between v m pin and v dd pin v dd = 1.8v, v m = 0v 150 300 500 k? r vms resistance between v m pin and v ss pin v dd = 3.5v, v m = 1.0v 10 30 50 k? v 0cha 0v battery charge starting charger voltage 0v battery charging available 1.2 v v 0inh 0v battery charge inhibition battery voltage 0v battery charging unavailable 0.45 v v ovchg overvoltage charger detection voltage v dd = 3.5v 6.0 8.0 10.0 v v ovchgr overvoltage charger release voltage v dd = 3.5v 5.3 7.3 9.3 v t cu overcharge detection delay time t cu 0.8 t cu t cu 1.2 ms t dl o verdischarge detection delay time t dl 0.7 t dl t dl 1.3 ms t doc discharge overcurrent detection delay time t doc 0.8 t doc t doc 1.2 ms t short load short - circuiting detection delay time t short 0.8 t short t short 1.2 s t coc charge overcurrent detection delay time t coc 0.8 t coc t coc 1.2 ms
AP9101C document numb er: ds37771 rev. 3 - 2 6 of 18 www.diodes.com december 2015 ? diodes incorporated AP9101C electrical characteristics ( c ont inued ) ( t a = - 40 c to + 85 c, v dd = 3.5v, v ss = 0v, r1 = 33 0? , r2 = 2.7 k?, c1 = 100nf, unless otherwise specified . ) symbol parameter test conditions min typ max unit v cu overcharg e detection voltage v cu - 0.060 v cu v cu +0.040 v v cl overcharge release voltage v cl v cu v cl - 0.080 v cl v cl +0.065 v v cl = v cu v cl - 0.060 v cl v cl +0.040 v v dl overdischarge detection voltage v dl - 0.110 v dl v dl +0.130 v v du overdischarge release voltage v du v dl v du - 0.150 v du v du +0.190 v v du = v dl v du - 0.110 v du v du +0.130 v v doc discharge overcurrent detection voltage v doc - 0.021 v doc v doc +0.024 v v short load short - circuiting detection voltage v short - 0.34 v short v short +0.34 v v coc charge overcurre nt detection voltage v coc - 0.040 v coc v coc +0.040 v i cc current consumption during operation v dd = 3.5v , v m = 0v 1.0 3.0 7.0 a i stb current consumption at power - down v dd = 1.8v , v m pin floating power - down mode 1.0 a without power - down mode (aut o - wake - up) 8 r coh co pin resistance h v dd = 3.5v, v co = 3.0v, v m = 0v 1.2 6 15 k ? r col co pin resistance l v dd = 4.5v, v co = 0.5v, v m = 0v 1.2 4 15 k? r doh do pin resistance h v dd = 3.5v, v do = 3.0v, v m = 0v 1.2 5 15 k? r dol do pin resistance l v dd = 1.8v, v do = 0.5v, v m = 0v 1.2 5 15 k? r vmd resistance between v m pin and v d d pin v dd = 1.8v , v m = 0v 100 300 650 k? r vms resistance between v m pin and v ss pin v dd = 3.5v , v m = 1.0v 5 30 65 k? v 0cha 0v battery charge starting charger voltage 0v battery charging available 1. 2 v v 0inh 0v battery charge inhibition battery vo ltage 0v battery charging unavailable 0.3 v v ovchg overvoltage charger detection voltage v dd = 3.5v 5.5 8.0 10.5 v v ovchgr overvoltage charger release voltage v dd = 3.5v 5.0 7.3 9.5 v t cu overcharge detection delay time t cu 0.6 t cu t cu 1.4 ms t dl overdischarge detection delay time t dl 0.55 t dl t dl 1.45 ms t doc discharge overcurrent detection delay time t doc 0.6 t doc t doc 1.4 ms t short load short - circuiting detection delay time t short 0.6 t short t short 1.4 s t coc charge overcurrent dete ction delay time t coc 0.6 t coc t coc 1.4 ms
AP9101C document numb er: ds37771 rev. 3 - 2 7 of 18 www.diodes.com december 2015 ? diodes incorporated AP9101C operation description operation mode 1. normal status the ap9101 c monitors the battery voltage between the v dd p in and v ss p in as well as the voltage difference between the v m p in and v ss pin to control ba ttery charging and discharging by co and do p ins. when the battery voltage is between overdischarge detection voltage (v dl ) and overcharge detection voltage (v cu ), as well as the v m p in voltage is between the charge overcurrent detection voltage (v coc ) and discharge overcurrent detection voltage (v doc ), the co and do p in of the ap9101 c will output high level and turn on charge and discharge mosfets. in these conditions, the battery can charge and discharge freely. also, r vmd and r vms do not connect to v dd a nd v ss p ins in this status. 2. overcharge status if the battery voltage is more than v cu during charging status for the overcharge detection delay time (t cu ) or longer, the ap9101 c turns off the charge mosfet by setting low level to co p in to stop charging. r vmd and r vms are not connected in overcharge status. when v m p in voltage is lower than v doc and battery voltage falls below v cl , the ap9101 c will release from overcharge status. when v m p in voltage is equal to or more than v doc and battery voltage falls below v cu , the ap9101 c will release from overcharge status. 3. overdischarge status if the battery voltage is less than v dl during discharging status for the overdischarge detection delay time (t dl ) or longer, the ap9101 c turns off the discharge mosfet by s etting low level to do p in to stop discharging. in overdischarge status, r vmd is connected to v dd and v m pi n voltage is pulled up to v dd by r vmd , but r vms is not connected. for stand - by version, the ap9101 c recovers normal status from overdischarge status only by charging the battery through the charger. when v m pin voltage to v ss p in voltage is less than typical - 0.7v and the battery voltage rises over v dl , the ap9101 c will release from overdischarge status. if v m p in voltage to v ss p in voltage is higher than typical - 0.7v, the ap9101 c will release from overdischarge status until the battery voltage rises over v du . for auto - wake - up version AP9101Ca , the device recovers to normal status from overdischarg e status if either of these two conditions are satisfi ed. if charger is connected: the AP9101Ca overdischarge status is released in the same way as described above in AP9101C overdischarge status section. if no charger is connected: 1) t he battery voltage reaches the overdischarge release voltage (v du ) o r higher; 2) m aintains continuous time more than o verdischarge release delay time t dlr . 4. discharge overcurrent and short current status when the battery is in discharge over current status, if the voltage of the v m pi n to v ss p in is equal or mor e than v doc to v short . for the overdischarge current detection delay time (t doc ) or longer , the ap9101 c turns off the discharg e mosfet by setting low level to do p in to stop discharging. when the battery is in short current status, if the voltage of the v m p in to v ss p in is equal to or more than v short , for the short current detection delay time or longer , the ap9101 c turns off the discharg e mosfet by setting low level to do pin to stop discharging. in discharge overcurrent or short current status, r vms is connected to v ss but r vmd is not connected. the voltage of v m pi n is almost equal to v dd as long as the load is connected. when the load is disconnected, the voltage of v m p in will become almost equal to v ss ( due to r vms being connected ) and then the ap9 101 c will release from discharge overcurrent or short current status . 5. charge overcurrent status when the battery is in charge over current status, if the voltage of the v m p in to v ss p in is equal to or less than v coc for the charge over current detection de lay time (t coc ) or longer, the ap9101 c turns off the charg e mosfet by setting low level to co p in to stop charging.
AP9101C document numb er: ds37771 rev. 3 - 2 8 of 18 www.diodes.com december 2015 ? diodes incorporated AP9101C operation description (cont inued ) 6. 0v battery charging function (option) this function is available as an option and can be factory set i nternally. AP9101C has this function built in. 0v charging function permits charger to recharge the battery whose voltage is 0v due to self - discharge. if 0v charging function is not present, the device will prevent charger to recharge the battery whose vol tage is 0v due to self - discharge. (if a device without 0v charging function is needed, please contact diodes sales team) 7. overvoltage charger detection circuit this function is used to monitor the charger voltage between the v dd p in and v m p in, and when th is voltage exceeds overvoltage charger detection voltage (8.0v typ ), the ap9101 c will set co p in low level to turn off charge mosfet . w hen this voltage drops below overvoltage charger release voltage (7.3v typ ), co p in will be set to high level and turn on charg e mosfet. there are no delay times set for detection and release . 8. power - down mode or auto - wake - up function option in device with power - down function, during p ower - down mode, device enters the overdischarge status. the ic enters sleep mode a nd the current consumption becomes very low , typically 0.1 a . to release from power - down status to the normal status, charger connection is required. in device with auto - wakeup mode, t he ic remains active in the o verdischarge state. the ic is released int o the normal state by the operation that increases the battery voltage more than o verdischarge release voltage.
AP9101C document numb er: ds37771 rev. 3 - 2 9 of 18 www.diodes.com december 2015 ? diodes incorporated AP9101C time chart (1) overcharge and overdischarge detection v c u v c l v d l v d u v d d v s s v s s v d d v m v d d v d o c v s s v p - v c o c v d d d o c o v m 2 1 r e d l i n e i s f o r n o s h u t d o w n m o d e v e r s i o n s 1 : c h a r g e r c o n n e c t i o n s 2 : l o a d c o n n e c t i o n 1 : t d l 2 : t c u 2 1 s 1 s 1 s 2 s 2
AP9101C document numb er: ds37771 rev. 3 - 2 10 of 18 www.diodes.com december 2015 ? diodes incorporated AP9101C time chart (cont inued ) (2) discharge overcurrent detection vcu vcl vdl vdu vdd vss vss vdd vm vdd vshort vss vdo c vdd do co vm 1 2 s 1 s 2 1 : t doc 2 : t short s 1 : connect over current load s 2 : connect short current load
AP9101C document numb er: ds37771 rev. 3 - 2 11 of 18 www.diodes.com december 2015 ? diodes incorporated AP9101C time chart (cont.) (3) charge overcurrent detection v c u v c l v d l v d u v d d v s s v s s v d d v m v d d v s s v p - v c o c v d d d o c o v m 1 s 1 1 : t c o c s 1 : c o n n e c t o v e r c u r r e n t c h a r g e r
AP9101C document numb er: ds37771 rev. 3 - 2 12 of 18 www.diodes.com december 2015 ? diodes incorporated AP9101C ordering information v oltage and delay time combination part number overcharge detection voltage v cu overcharge release voltage v cl over - discharge detection voltage v dl over - discharge release voltage v du discharge overcurrent detection voltage v doc load short detection voltage v short charge overurrent detection voltage v coc over voltage c harger detection voltage v ovchg over voltage charger release voltage v ovchgr power - down function overcharge protection mode delay time 0v battery charge function ap9 101cxxx - aa trg1 4.375v 4.175v 2.500v 2.900v 0.150v 0.700v - 0.150v 8.0v 7.3v selectable au to r elease option 1 permission ap9 101cxxx - a btrg1 4.425v 4.225v 2.500v 2.900v 0.150v 0.700v - 0.150v 8.0v 7.3v selectable auto r elease option 1 permission ap9 101cxxx - a ctrg1 4.375v 4.175v 2.500v 2.900v 0.095v 0.700v - 0.095v 8.0v 7.3v selectable auto r elease option 1 permission ap9 101cxxx - a dtrg1 4.375v 4.175v 2.500v 2.900v 0.120v 0.700v - 0.120v 8.0v 7.3v selectable auto r elease option 1 permission ap9 101cxxx - a etrg1 4.200v 4.100v 2.500v 3.000v 0.300v 0.550v - 0.100v 8.0v 7.3v selectable auto r elease option 1 permission ap9 101cxxx - a ftrg1 4.375v 4.175v 2.500v 2.900v 0.180v 0.700v - 0.180v 8.0v 7.3v selectable auto r elease option 1 permission ap9 101cxxx - a gtrg1 4.375v 4.175v 2.500v 2.900v 0.075v 0.700v - 0.075v 8.0v 7.3v selectable auto r elease option 1 permission ap9 101cxxx - a htrg1 4.425v 4.225v 2.500v 2.900v 0.075v 0.700v - 0.075v 8.0v 7.3v selectable auto r elease option 1 permission ap9 101cxxx - a itrg1 4.500v 4.300v 2.400v 2.800v 0.150v 0.700v - 0.075v 8.0v 7.3v selectable auto r elease option 1 permission ap9 101cx xx - a jtrg1 4.375v 4.175v 2. 4 00v 2.800v 0.125v 0.700v - 0.125v 8.0v 7.3v selectable auto r elease option 1 permission ap9 101cxxx - a ktrg1 4.250v 4.050v 2.400v 3.000v 0.150v 0.700v - 0.150v 8.0v 7.3v selectable auto r elease option 1 permission ap9 101cxxx - a ltrg1 4.275v 4.175v 2.300v 2.400v 0.180v 0.700v - 0.180v 8.0v 7.3v selectable auto r elease option 1 permission ap9 101cxxx - a mtrg1 4.375v 4.175v 2.300v 2.400v 0.180v 0.700v - 0.180v 8.0v 7.3v selectable auto r elease option 1 permission ap9 101cxxx - a ntrg1 4.225v 4.0 25v 3.200v 3.400v 0.060v 0.450v - 0.060v 8.0v 7.3v selectable auto r elease option 1 permission ap9 101cxxx - a otrg1 4.425v 4.225v 2.500v 2.900v 0.064v 0.228v - 0.073v 8.0v 7.3v selectable auto r elease option 1 permission a p 9 1 0 1 c x x x C x x x x x x p a c k i n g p a c k a g e t r : t a p e & r e e l k : s o t 2 5 k 6 : s o t 2 6 p r o d u c t n a m e p r o d u c t c o d e g 1 : g r e e n v o l t a g e & d e l a y t i m e c o m b i n a t i o n c o d e r o h s / g r e e n p o w e r d o w n m o d e b l a n k : y e s a : n o ( a u t o - w a k e - u p )
AP9101C document numb er: ds37771 rev. 3 - 2 13 of 18 www.diodes.com december 2015 ? diodes incorporated AP9101C ordering information (continued ) delay time option overview delay time option overcharge detectio n delaytime (t cu ) overdischarge detection delay time (t dl ) overdischarge current detection delay time (t doc ) overcharge current detection delay time (t coc ) load short circuiting detection delay time (t short ) 1 1,000ms 115ms 10ms 10ms 320 s 2 125ms 32ms 8ms 8ms 160s 3 1,000ms 20ms 12ms 10ms 320s 4 1,000ms 42ms 10ms 10ms 320s 5 1,000ms 115ms 10ms 10ms 160s
AP9101C document numb er: ds37771 rev. 3 - 2 14 of 18 www.diodes.com december 2015 ? diodes incorporated AP9101C marking informatio n ( note 6 ) product package part number marking id packing type green green AP9101C sot 25 AP9101Ck - a a trg1 gqa tape & reel AP9101Ck - a b trg1 g6u tape & reel AP9101Ck - a c trg1 gqj tape & reel AP9101Ck - a d trg1 gqk tape & reel AP9101Ck - aetrg1 gqd tape & reel AP9101Ck - aftrg1 gql tape & reel ap 9101ck - agtrg1 gqm tape & reel AP9101Ck - ahtrg1 gqn tape & reel AP9101Ck - aitrg1 gqp tape & reel AP9101Ck - ajtrg1 gqq tape & reel AP9101Ck - aktrg1 gqg tape & reel AP9101Ck - altrg1 gqr tape & reel AP9101Ck - amtrg1 gqs tape & reel AP9101Ck - antr g1 gqt tape & reel AP9101Ck - aotrg1 grt tape & reel AP9101Cak - aatrg1 gra tape & reel AP9101Cak - abtrg1 gsc tape & reel AP9101Cak - actrg1 grj tape & reel AP9101Cak - adtrg1 grk tape & reel AP9101Cak - aetrg1 grd tape & reel AP9101Cak - aftrg1 gr l tape & reel AP9101Cak - agtrg1 grm tape & reel AP9101Cak - ahtrg1 grn tape & reel AP9101Cak - aitrg1 grp tape & reel AP9101Cak - ajtrg1 grq tape & reel AP9101Cak - aktrg1 grg tape & reel AP9101Cak - altrg1 grr tape & reel AP9101Cak - amtrg1 grs ta pe & reel AP9101Cak - antrg1 gst tape & reel AP9101Cak - aotrg1 gtt tape & reel
AP9101C document numb er: ds37771 rev. 3 - 2 15 of 18 www.diodes.com december 2015 ? diodes incorporated AP9101C marking informatio n (continued ) AP9101C sot 26 AP9101Ck6 - aatrg1 gqb tape & reel AP9101Ck6 - abtrg1 gqc tape & reel AP9101Ck6 - actrg1 gsj tape & reel AP9101Ck6 - adt rg1 gsk tape & reel AP9101Ck6 - aetrg1 gqe tape & reel AP9101Ck6 - aftrg1 gsl tape & reel AP9101Ck6 - agtrg1 gsm tape & reel AP9101Ck6 - ahtrg1 gsn tape & reel AP9101Ck6 - aitrg1 gsp tape & reel AP9101Ck6 - ajtrg1 gsq tape & reel AP9101Ck6 - aktrg1 gqh tape & reel AP9101Ck6 - altrg1 gsr tape & reel AP9101Ck6 - amtrg1 gss tape & reel AP9101Ck6 - antrg1 gqu tape & reel AP9101Ck6 - aotrg1 gru tape & reel AP9101Cak6 - aatrg1 grb tape & reel AP9101Cak6 - abtrg1 grc tape & reel AP9101Cak6 - actrg1 g tj tape & reel AP9101Cak6 - adtrg1 gtk tape & reel AP9101Cak6 - aetrg1 gre tape & reel AP9101Cak6 - aftrg1 gtl tape & reel AP9101Cak6 - agtrg1 gtm tape & reel AP9101Cak6 - ahtrg1 gtn tape & reel AP9101Cak6 - aitrg1 gtp tape & reel AP9101Cak6 - ajtrg 1 gtq tape & reel AP9101Cak6 - aktrg1 grh tape & reel AP9101Cak6 - altrg1 gtr tape & reel AP9101Cak6 - amtrg1 gts tape & reel AP9101Cak6 - antrg1 gsu tape & reel AP9101Cak6 - aotrg1 gtu tape & reel note : 6. current voltage versions are built by delay time option 1. if any other voltage versions or delay time option products are needed, please contact with the local sales office.
AP9101C document numb er: ds37771 rev. 3 - 2 16 of 18 www.diodes.com december 2015 ? diodes incorporated AP9101C a1 d e e1 e b a2 a1 seating plane l c a e1 a3 package outline dimensions please see ap02002 at http://www.diodes.com/datasheets/ap02002.pdf for the latest versi on. sot25 sot25 dim min max typ a 0.35 0.50 0.38 b 1.50 1.70 1.60 c 2.70 3.00 2.80 d - - 0.95 h 2.90 3.10 3.00 j 0.013 0.10 0.05 k 1.00 1.30 1.10 l 0.35 0.55 0.40 m 0.10 0.20 0.15 n 0.70 0.80 0.75 ? ? ? al l dimensions in mm sot26 sot26 dim min max typ a1 0.013 0.10 0.05 a2 1.00 1.30 1.10 a3 0.70 0.80 0.75 b 0.35 0.50 0.38 c 0.10 0.20 0.15 d 2.90 3.10 3.00 e - - 0.95 e1 - - 1.90 e 2.70 3.00 2.80 e1 1.50 1.70 1.60 l 0 .35 0.55 0.40 a - - 8 a1 - - 7 all dimensions in mm a m j l d b c h k n
AP9101C document numb er: ds37771 rev. 3 - 2 17 of 18 www.diodes.com december 2015 ? diodes incorporated AP9101C suggested pad layout please see ap02001 at http://www.diodes.com/datasheets/ap02001.pdf for the latest version. sot25 dimensions value (in mm) z 3.20 g 1.60 x 0.55 y 0.80 c1 2.40 c2 0.95 sot26 dimensions value (in mm) c 2.40 c1 0.95 g 1.60 x 0.55 y 0.80 y1 3.20 c1 y1 g x y c x z y c1 c2 c2 g
AP9101C document numb er: ds37771 rev. 3 - 2 18 of 18 www.diodes.com december 2015 ? diodes incorporated AP9101C important notice diodes incorporated makes no warranty of any kind, express or imp lied, with regards to this document, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose (and their equivalents under the laws of any jurisdiction). diodes incorporated and its subsidiaries reser v e the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. diodes incorporated does not assume any liability a rising out of the application or use of this document or any product described herein; neither does diodes incorporated convey any license under its patent or trademark rights, nor the rights of others. any customer or user of this document or products described herein in such applic ations shal l assume all risks of such use and will agree to hold diodes incorporated and all the companies whose products are represented on diod es incorporated website, harmless against all damages. diodes incorporated does not warrant or accept any liability wha tsoever in respect of any products purchased through unauthorized sales channel. should customers purchase or use diodes incorporated products for any unintended or unauthorized application, customers shall indemnify and hold diodes incorporated and its re presentatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. products described herein may be cov ered by one or more united states, international or foreign patents pending. product names and markings noted herein may also be covered by one or more united states, international or foreign trademarks. this document is written in english but may be tran slated into multiple languages for reference. only the english version of this document is the final and determinative format released by diodes incorporated. life support diodes incorporated products are specifically not authorized for use as critical c omponents in life support devices or systems without the express written approval of the chief executive officer of diodes incorporated. as used herein: a. life support devices or systems are devices or systems which: 1. are intended to implant into t he body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided i n the labeling can be reasonably expected to result in significant injury to the user. b. a critical componen t is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. customers represent that they have all necessary ex pertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety - related requirements concerning their products and any use of diode s incorporated products in such safety - critical, life support devices or systems, notwithstanding any devices - or systems - related information or support that may be provided by diodes incorporated. further, customers must fully indemnify diodes incorporat e d and its representatives against any damages arising out of the use of diodes incorporated products in such safety - critical, life support devices or systems. copyright ? 2015, diodes incorporated www.diodes.com

▲Up To Search▲

Price & Availability of AP9101C

	To Download AP9101C Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .